1) EVA
乙烯-乙酸乙烯共聚物
1.
It prepared the PP/EVA blends with different blending ratio of PP and EVA, and tested the impact strength and tensile strength of the blends.
将不同配比的聚丙烯(PP)和乙烯-乙酸乙烯共聚物(EVA)进行共混,测试了共混物的拉伸强度和冲击强度;用差示扫描量热法研究了共混物的结晶性能;用扫描电镜(SEM)二次电子成像系统分析了试样的断口形貌,研究了EVA含量对共混物力学性能的影响。
2.
The flame retardant composites were prepared with EVA served as matrix,MH as flame retardant,non-toxic and high effective lubricant MCA as synergist.
以乙烯-乙酸乙烯共聚物(EVA)为基体树脂,氢氧化镁(MH)为阻燃剂,以无毒、高润滑的三聚氰胺氰尿酸盐(MCA)为协同剂,制备了MCA协同EVA/MH复合阻燃体系,系统研究了其力学性能、燃烧性能、加工流动性能和尺寸稳定性。
3.
Effects of resin matrix,conductive material,lubricant,and antioxidant on properties of semiconductive shielding material of thermoplastic EVA were studied.
研究了基体树脂、导电材料、润滑剂、抗氧剂对热塑性乙烯-乙酸乙烯共聚物(EVA)半导电屏蔽料性能的影响,确立了EVA半导电屏蔽料配方:EVA100份,导电炭黑55份,润滑剂8。
2) ethylene-vinyl acetate copolymer
乙烯-乙酸乙烯共聚物
1.
An high elasticity, injection cross-linked, closed-cell foam was prepared based on a polymer blend of ethylene-vinyl acetate copolymer (EVA) and ethylene propylene diene tercopolymer (EPDM) rubber with an inorganic filler (TA).
乙烯-乙酸乙烯共聚物(EVA)与三元乙丙橡胶(EPDM)共混,加入滑石粉填料(TA),用过氧化二异丙苯(DCP)引发交联,偶氮二碳酰胺(ADC)发泡,得到了一次性注射交联闭孔式发泡成型的高弹性材料。
3) ethylene/vinyl acetate copolymer
(乙烯/乙酸乙烯酯)共聚物
4) EVA
乙烯-乙酸乙烯酯共聚物
1.
The influence of filler type,filler level,the initial mixing temperature,mixing time and rotor speed on the properties of TPU/EVA blend was investigated by using a torque rheometer.
采用转矩硫化仪考察填料种类和用量、混炼初始温度、混炼时间和转子转速对热塑性聚氨酯(TPU)/乙烯-乙酸乙烯酯共聚物(EVA)共混物性能的影响。
2.
The ethylene-vinyl acetate copolymer (EVA)/clay nanocomposites were successfully prepared through melt intercalation process.
通过熔体插层制备了乙烯-乙酸乙烯酯共聚物(EVA)/粘土纳米复合材料。
3.
An injection super light blowing material of ethylene-vinyl acetate copolymer (EVA) and ethylene-acrylate copolymer grafted with maleic anhydride (Fusabond), which has good properties to meet the adidas footwear standard requirements, was developed and put into production of the injection molding midsole of adidas sport-shoe.
注射硫化交联发泡成型的乙烯-乙酸乙烯酯共聚物(EVA)与马来酸酐接枝的乙烯-丙烯酸酯的共聚物(Fusabond)超轻发泡材料,其力学性能符合adidas鞋材标准,可用于生产注射adidas运动鞋中底;利用流变仪测定转矩和发泡压力随时间的变化来研究其硫化交联反应和发泡作用的动力学,在转矩上升阶段为一级反应,给出了硫化交联反应的速率常数k为1。
5) ethylene-vinyl acetate copolymer
乙烯-乙酸乙烯酯共聚物
1.
Performance of ethylene-vinyl acetate copolymer/styrene-butadiene-styrene block copolymer compound modified asphalt by dynamic vulcanization;
动态硫化乙烯-乙酸乙烯酯共聚物/苯乙烯-丁二烯-苯乙烯嵌段共聚物复合改性沥青的性能
2.
This paper studied the effects of carbon black(CB)on miscibility of high impact polystyrene/ethylene-vinyl acetate copolymer(HIPS/EVA)and predicted the phase morphological transition of the blending system.
研究了炭黑(CB)对高抗冲聚苯乙烯(HIPS)/乙烯-乙酸乙烯酯共聚物(EVA)共混体系相容性的影响,并预测了共混体系的相形态转变点。
3.
The copolymer(VAA-Eu) of vinyl acetate and europium acrylate is blended with ethylene-vinyl acetate copolymer(EVA) to prepare a blend(EVA/VAA-Eu) film.
以乙酸乙烯酯和丙烯酸铕的共聚物(VAA-Eu)与乙烯-乙酸乙烯酯共聚物(EVA)的共混物(EVA/VAA-Eu)制备薄膜,通过测定荧光光谱和透过薄膜的紫外光辐照度,研究其对紫外光的遮挡和光转换作用。
6) vinyl acetate ethylene
乙酸乙烯-乙烯共聚物
1.
The blended membrane based on the water-soluble polymer polyvinyl alcohol (PVA) and water-insoiuble vinyl acetate ethylene (VAE) latex was prepared by solution casting method, which is a new approach for the pesticide membrane.
以水溶性聚合物聚乙烯醇(PVA)和水不溶性聚合物乙酸乙烯-乙烯共聚物(VAE)乳液为原料,采用溶液共混法制备了PVA-VAE共混膜,为农药成膜剂的制备开辟了新途径。
补充资料：乙烯-乙酸乙烯共聚物
分子式：
CAS号：
性质：是由乙烯和醋酸乙烯共聚而得的一种热塑性树脂。在乙酸乙烯含量较高时，其弹性、柔软性、黏合性、相容性、透明性、溶解性较好。乙酸乙烯含量小于10％时，比聚乙烯柔软，耐冲击强度好，用作包装袋和薄膜以及注射模塑件，电缆覆层、玩具等。乙酸乙烯在10％～20％时，透明性良好，耐寒耐应力开裂，用于制农业薄膜，医疗用具等，乙酸乙烯含量在20％～40％时，具有良好的黏合性，用作热熔胶黏剂、涂料等。乙酸乙烯含量在45％～55％时，弹性良好，用作特种橡胶，与其他橡胶相容性好，加工性也好，可用过氧化物硫化，与硫化橡胶不相上下；乙酸乙烯含量在65％～95％时为乳液，可用作纤维、纸张等的胶黏剂。
CAS号：
性质：是由乙烯和醋酸乙烯共聚而得的一种热塑性树脂。在乙酸乙烯含量较高时，其弹性、柔软性、黏合性、相容性、透明性、溶解性较好。乙酸乙烯含量小于10％时，比聚乙烯柔软，耐冲击强度好，用作包装袋和薄膜以及注射模塑件，电缆覆层、玩具等。乙酸乙烯在10％～20％时，透明性良好，耐寒耐应力开裂，用于制农业薄膜，医疗用具等，乙酸乙烯含量在20％～40％时，具有良好的黏合性，用作热熔胶黏剂、涂料等。乙酸乙烯含量在45％～55％时，弹性良好，用作特种橡胶，与其他橡胶相容性好，加工性也好，可用过氧化物硫化，与硫化橡胶不相上下；乙酸乙烯含量在65％～95％时为乳液，可用作纤维、纸张等的胶黏剂。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条