1) solidification mode
凝固方式
1.
Combination with the concept MDE,through testing of the dynamic curves of casting solidification about Al-Si eutectic alloy in lost foam process,obtain the solidification mode and effect of the casting section module and the pouring temperature on MDE.
在对干砂消失模铸造共晶铝硅合金凝固动态曲线测试的基础上,结合共晶糊状凝固程度MDE(Mushy Solidification Degree of Eutectic Alloy)的概念,总结出干砂消失模铸造铝硅合金凝固方式及其铸件断面模数、浇注温度变化对凝固方式的影响和相关铸造工艺设计原则,并通过试验予以验证。
2.
The solidification mode evolving regulars of ZA42 in different current intensity was studied in this paper.
研究了ZA42合金在不同电流强度作用下凝固方式的演变规律。
3.
The solidification modes and morphology of liquid phase of semi-solid AZ91D Mg alloy by li- quid quenching were investigated.
采用快速液淬方法分析研究了AZ91D镁合金半固态液相的凝固方式和组织形貌,结果表明:镁合金半固态液相的凝固方式与冷却速度所决定的过冷度有重要关系。
2) solidification mode
凝固模式
1.
Microstructures and solidification mode of continuous casting slabs of austenitic stainless steel Cr17Mn6Ni4Cu2N
Cr17Mn6Ni4Cu2N奥氏体不锈钢连铸坯组织及凝固模式
2.
The results showed that the solidification mode of sample No.
试验结果表明:由于氮含量的差异,低氮式样(1号)、高氮式样(2号)的凝固模式不同,且他们随着冷却速度的增加,铁素体及晶粒内部沉淀相的含量变化趋势存在明显的差别。
3.
The results show that the solidification mode of sample 1 with lower N2 content was different from sample 2 which has higher N2 content,and significant difference of the trend of change in the ferrite and precipitation phase content inside the crystal between them appeared as their cooling speed increased.
试验结果表明:由于氮含量的差异,低氮钢式样(1号)与高氮钢式样(2号)的凝固模式不同,且它们随着冷却速度的增加,铁素体及晶粒内部沉淀相的含量变化趋势存在明显的差别。
3) the frozen format
凝固格式
1.
In part one the frozen format is analysed.
第一章对凝固格式进行研究。
4) directionally solidification
方向性凝固
1.
"fine grain + directionally solidification + heat isothermal process" were performed for achievement of the prevent.
在弯曲共振无法避免的情况下 ,从提高动力涡轮叶片的疲劳抗力入手 ,采用细晶 +方向性凝固 +热等静压的复合成型工艺 ,成功地解决了这一故
5) batch-fed tube
管式凝固浴
补充资料：油气田开发方式(见油气田生产方式)
油气田开发方式(见油气田生产方式)
development pattern of oil and gas field:see recovery pattern of oil and gas field
a垃d gas月e卫d) 、‘。尸卫Jlent见油气田小冰、*pa士teroof ojl
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条