2) isothermal cure
等温固化
1.
It was found that the increase of E′ during isothermal cure process at high temperatures is different from the one at low temperatures.
采用动态力学分析法(DMA)对648环氧预浸料的等温固化过程进行了表征分析。
3) non-isothermal solidification
非等温凝固
1.
Phase-field simulation of influence of anisotropy on process of non-isothermal solidification;
各向异性影响非等温凝固过程的相场法模拟
2.
Phase-field Simulation of Non-isothermal Solidification of Binary Alloy;
二元合金非等温凝固过程的相场法模拟
3.
Phase-field simulation of non-isothermal solidification dendrite growth of binary alloy under the force flow
强迫对流影响二元合金非等温凝固枝晶生长的相场法模拟
4) non-isothermal crystallization
非等温晶化
1.
Computation methods of activation energy of amorphous alloy with non-isothermal crystallization;
非晶合金非等温晶化激活能的计算方法
2.
Kinetic performance of non-isothermal crystallization of amorphous Co-Cu-B alloy nanopowder
非晶态Co-Cu-B纳米合金粉末的非等温晶化动力学性能
3.
One was non-isothermal crystallization kinetics at constant heating rate,which could be analyzed by the Kissinger and DoyleOzawa method.
5非晶合金的非等温晶化的动力学行为。
5) non-isothermal oxidation
非等温氧化
1.
With the help of thermogravimetric analysis technique,non-isothermal oxidation kinetics of polycrystalline graphite was investigated by model-fitting and model-free methods,and the microstruc- ture of the same surface of different weight loss was observed by SEM.
通过热重分析技术用模式函数和无模式函数法研究了多晶石墨材料的非等温氧化动力学,并利用扫描电镜观察了该材料同一表面不同氧化程度的微观结构。
6) anisothermal oxidation
非等温氧化
1.
The mass loss and mass gain behavior during anisothermal oxidation of three kinds of C-SiC-B4C composites with the varieties of B4C/SiC ratio was studied in the paper.
研究B4C/SiC值不同的三种C-SiC-B4C复合材料在非等温氧化过程中的失重/增重行为。
补充资料:非等温吸收
气液两相的温度在过程中发生显著变化的吸收操作。如果被处理的气体混合物中含有可被吸收的溶质量较大,而且溶质组分溶于吸收剂时的溶解热(物理吸收时)或与吸收剂之间的反应热(化学吸收时)较大,则吸收过程中释放出来的热量远大于设备散热量和少量吸收剂汽化所消耗的热量。两相的温度会随吸收的进行发生明显的变化,吸收剂的出口温度会比进口温度高得多,在吸收设备中也会有不相同的温度分布。温度升高将影响气液平衡(见汽液平衡)关系,使传质推动力明显减小,同时传质系数也随温度而有所变化。通常温度升高使气相传质分系数减小,使液相传质分系数和反应速度(在化学吸收中)增大。对于高溶解度溶质的吸收,气阻控制传质,温度升高时对吸收很不利;对于低溶解度溶质的吸收,液阻控制传质,适当的升温能达到较高的传质总系数,但温度太高时,因为传质推动力下降太多,对吸收仍然不利。为此,对非等温吸收来说,一般须采用适当的冷却措施,以维持适当的操作温度,保证吸收产物的质量。从吸收设备中移去热量的方法有:①循环冷却(图1)。将部分出塔液体经塔外冷却后送回塔顶,以增加塔内液体流量,减少温升,多用于填充塔。②内部冷却。在吸收塔内部安装冷却装置,移去热量,多用于板式塔。③中间冷却(图2)。在多段吸收塔的段间进行冷却,以移去热量。
非等温吸收在工业生产中应用颇广,如硫酸生产中三氧化硫的吸收,硝酸生产中氮的氧化物的吸收等。近年来,关于非等温吸收的实验和计算方法的研究都有加强。
非等温吸收在工业生产中应用颇广,如硫酸生产中三氧化硫的吸收,硝酸生产中氮的氧化物的吸收等。近年来,关于非等温吸收的实验和计算方法的研究都有加强。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条