说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 成品拉拔
1)  finish drawing
成品拉拔
1.
To introduce the production process technology of rough drawing, heat treatment and finish drawing of heavy coil steel wire and the transportation manner among procedures.
介绍大盘重粗拉、热处理、成品拉拔生产工艺技术以及各工序之间的运输方式,说明大盘重连续生产线的设计应从钢丝生产的总体流程考虑。
2)  machanical drawing
机械拉拔成型
3)  salad makings
沙拉成品
4)  drawing [英]['drɔ:ɪŋ]  [美]['drɔ·ɪŋ]
拉拔
1.
Geometric Parameters and Numerical Simulation of Drawing Process for Odd Number Side Drill Hollow Steel Stem;
奇数边中空钢钎杆几何参数及拉拔过程数值模拟
2.
Forming Process Design of Pipe Drawing Based on Multi-objective Optimization;
基于多目标优化的钢管拉拔成形过程设计
3.
3D FEM simulation of cross tube drawing process;
十字形钢管拉拔成形的三维有限元模拟
5)  draw [英][drɔ:]  [美][drɔ]
拉拔
1.
5% single pass draught to draw,taking all these measures can get the product with high strength,high toughness and definite bending property.
5%的单道次拉拔,可获得高强度、高韧性且具有一定弯曲性能的产品。
2.
Some methods of forcing lubrication under drawing were introduced,and their characteristics were analyzed.
介绍了拉拔过程中强制润滑的几种方法,分析比较其优缺点,提出了把动、静压流体强制润滑两种方法相结合的设计方法。
3.
It is considered by examination and analysis that the main causes of brittle fracture in drawing and lower specific elongation of finished wire are local martensite existence for alloy elements’segregation, carbon segregation leading net cementite and the continuity of metal being destroyed by high nonmetal inclusion; the transverse crackles of steel wire surface are due to the deep.
 借助金相组织观察和电子探针检测,对PC钢丝生产中出现的质量问题进行研究,检测和分析认为拉拔脆断和成品钢丝延伸率低的主要原因是合金元素偏析导致局部马氏体存在、碳偏析引起网状渗碳体及严重的非金属夹杂物破坏金属的连续性;钢丝表面横裂主要是轧钢过程中折叠的表面氧化铁皮较深,或拉拔过程中润滑不良造成局部过热,导致表层产生马氏体引起的;钢丝表面划伤主要由线材出现耳子和椭圆度过大以及拉丝模安放不正所致。
6)  pull-out
拉拔
1.
Working mechanism of fully grouted bolt in pull-out working state;
拉拔工况下全长粘结锚杆工作机理
2.
The analysis of mechanical interacting between fiber and matrix was presented in this paper,the whole process of fiber pull-out load and pull-out displacement was carried out by using numerical method.
对纤维与基体的相互作用进行了力学分析,完成了纤维拉拔荷载与拉拔位移全过程的数值计算。
3.
As an important means for evaluating the surface modification of reinforcing fibers and the quality of composite interface,single fiber pull-out test has been highly regarded.
利用有限元软件,对纤维拉拔过程进行了数值模拟,分别得到不同时间下的应力和位移图及纤维拉拔时的应力状态及其对界面性能的影响。
补充资料:成品检验(见成品验证)

  
  成品检验(见成品验证)
  finished product inspection: see finished product verification

  山e叩Pinjian四n成品检脸(finishedp耐uct inspection)见成品脸证。
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条