1) workpiece deformation
工件变形
1.
According to the principle of the minimum complementary energy, a finite element method is presented to reveal the influence of multiple clamping forces and contact forces on workpiece deformations.
在考虑工件与夹具元件之间摩擦力的情况下,建立了多重夹紧力的大小、作用点以及夹紧顺序与接触力之间关系的力学模型,采用最小总余能原理的有限元求解方法,定量地分析了多重夹紧力与接触力对工件变形的影响;在此基础上发展了优选夹紧力大小、作用点以及夹紧顺序的数学模型。
2) lipped H-section tapered members
卷边工形变截面构件
1.
The in-plane stability bearing capacity of lipped H-section tapered members under both compression and bending is studied,and corresponding calculation formula is also given based on the existing formula of current Chinese related technical codes.
针对卷边工形变截面构件在压弯作用下的面内稳定承载性能进行研究,并在已有的卷边工形等截面压弯构件面内稳定承载力公式的基础上,参照CECS 102∶2002《门式刚架轻型房屋钢结构技术规程》中的变截面构件设计方法,给出卷边工形变截面构件压弯平面内稳定承载力的计算公式。
3) deformation condition
变形条件
1.
Effects of microalloying element and deformation condition on microstructure of ultrafine-grained medium and heavy plate;
微量元素和变形条件对超细晶中厚板显微组织的影响
2.
The effect of deformation condition on dynamic recrystallization of X60 Nb-microalloyed pipeline steel was studied on Gleeble-1500 simulator,which brings a strong theory base of producing X60 Nb-microalloyed pipeline steel by CSP processing.
为了消除利用CSP技术生产管线钢时较易出现的混晶缺陷,在Gleeble - 15 0 0热模拟实验机上对X6 0含Nb管线钢进行了高温压缩变形实验,研究了变形条件对其动态再结晶行为的影响,从而为利用CSP技术生产X6 0含Nb管线钢的工艺优化提供了一定的理论依
3.
The effect of deformation condition on dynamic recrystallization of 30MnSiV was studied on Gleeble-1500 simulator.
通过在Gleeble 1500热模拟实验机上对30MnSiV钢进行高温压缩变形实验,研究了变形条件对其动态再结晶行为的影响。
5) deformation of rolled wire
轧件变形
1.
The relationship of rolling tension with deformation of rolled wire by a high speed wire rod mill based on the process of φ 6 5 mm wire rod was studied in this papers.
5 mm盘条的工艺设计 ,研究了轧件在精轧机组中的轧制张力和轧件变形的关系 ,分析了辊径、孔槽磨损、进精轧机组坯料尺寸等因素对各架次轧制张力、轧件变形的影响 ,从而探讨合适的工艺调整方
6) element deformed
元件变形
补充资料：大坝内部变形观测(见水工建筑物变形观测)
大坝内部变形观测(见水工建筑物变形观测)
daba neibubianxing guanCe大坝内部变形观测见水工建筑物变形观测。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条