1) Veneer thickness variation
单板厚度偏差
2) thickness deviation
板厚偏差
1.
Through analyzing the demand of thickness deviation, a new monitoring method basing on ultrasonic measurement technique and computer control technique was put forwared.
基于板厚偏差在线监测这一问题展开研究，采用智能仪器的设计方法和手段，进行人造板厚度在线监测系统的研究设计。
3) thickness deviation
厚度偏差
1.
The effect of thickness deviation on the reflection spectra and phase shift of VCSELs has been analysed using optical transfer matrix method.
采用光学传输矩阵方法分析了厚度偏差对VCSEL的反射谱和反射相移产生的影响。
2.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill,rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a variety of roll length,plate width and rolling force is studied too.
针对由于轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析了轧辊承受载荷的分布情况,研究了宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
3.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill, rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a varity of roll length, plate width and rolling force is studied too.
针对轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析轧辊承受载荷的分布情况,研究宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
4) veneer thickness
单板厚度
1.
In this paper variation of veneer thickness in rotary-cutting had been researched by theory.
从理论上探讨了旋切过程中单板厚度的变化规律，结果表明：单板厚度总是小于或等于单板名义厚度，其变化与装刀高度、名义厚度及木段瞬时半径有关。
5) wall thickness deviation
壁厚度偏差
6) thickness difference of sheet
板料厚度差
补充资料：板带厚度测量
板带厚度测量
thickness measurement of plate and strip
bondai houdu eeliang板带厚度测量(thiekness measurement ofpfate and strip)指板带厚度尺寸的在线实时测量。这是提高成品率，保证板带材产品质量的重要措施，是实现生产过程自动化不可缺少的重要环节。(见厚度自动挂制) 板带厚度的在线测量可分为接触式测量和非接触式测量两类。接触式测量按工作原理分为电感式、差动变压器式、角位移式、磁栅式等。非接触式测量按工作原理分为射线式、微波式、激光式、气动式、涡流式等。在生产过程中，选用哪种测量方式，取决于板带的材质和生产过程工艺所提出的技术要求。非接触式测量得到广泛采用。 中国在2。世纪50年代开始对测厚仪进行了研究，现在已有了各种类型的测厚仪，对轧制生产线的自动控制起了很大的促进作用。各种类型测厚方法的仪器、应用范围和产地如表所列。 各种测厚仪器的性能、特点和应用扭李 (李由婉)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条