1) flame welding repair
火焰焊补
1.
Development and application of flame welding repair technique on coke oven;
火焰焊补技术在韶钢焦炉上的开发应用
2) flames spray-welding
火焰喷焊
1.
WC/Ni coating was made on TC4 alloys surface by using flames spray-welding,and the microstructure, composition,phase structure and microhardness of the coating were tested and analyzed.
采用火焰喷焊技术对TC4合金表面喷焊Ni基WC。
2.
The possibility of Ni-based WC coating on titanium alloys substrate through flames spray-welding technique was explored,and the microstructure and properties of the coating were determined using SEM,XRD and so on.
研究了在钛合金Ti-6A l-4V表面上采用火焰喷焊技术制备镍基碳化钨型自熔性合金涂层的可行性,利用SEM、XRD等手段分析了它的组织和性能。
3.
Two kinds of Ni-base coatings with 0% and 4% La2O3 addition respectively on titanium alloys substrate made by flames spray-welding technique were prepared, and their microstructure, elemental distribution, micro-hardness and tribological properties under dry sliding against steel were studied.
采用火焰喷焊技术在钛合金基体上制备了不加La2O3和加4%(质量分数)La2O3两种镍基涂层,分析了它们的显微组织、合金元素的扩散、显微硬度以及耐磨性能。
3) flame spray-welding
火焰喷焊
1.
Ni60+WC clad layers on the 45 steel substrate were produced by l aser cladding and flame spray-welding,respectively.
分别采用激光熔覆与粉末火焰喷焊两种技术在45钢基体表面制备Ni60+20%WC合金涂层,比较其组织结构和性能。
4) flame spray welding
火焰喷焊
1.
Failure of scourge-type reamer and feasibility of strengthening by flame spray welding NiWC coatings;
鞭式刀具的失效及火焰喷焊NiWC强化的可行性研究
2.
Generally it is deposited with nickel-based alloys through flame spray welding.
泥浆泵中的闸板起着调节流量的作用 ,由于其工况的要求 ,闸板必须具有耐磨损、耐腐蚀的性能 ,一般采用火焰喷焊的方法在闸板表面熔敷一层镍基合金 ,生产过程中发现 ,喷焊层常含有大量的气孔 ,致使该零件的合格率很低 ,且影响其使用寿命。
3.
The two coating techniques of powder flame spray welding and laser cladding were objectively compared from practice .
从实际出发对粉末火焰喷焊和激光熔覆两种涂膜工艺作了客观地比较 ,对它们的优缺点给予综合的评价 ,同时提出一些对实际应用具有指导意义的参考性建
5) torch brazing
火焰钎焊
1.
Application of oxy acetylene torch brazing in LF21 Al alloy;
氧—乙炔火焰钎焊在LF 21铝合金上的应用
2.
Under torch brazing condition, using brazing filler metals of Cu-based and Ag-based, a series of tests are investigated to braze Ti(C,N) based cermets and 45 steel, the micrographic structure of joints and shearing test results are analyzed, they show that Ti(C,N) based cermets has good brazability.
在火焰钎焊条件下 ,采用铜基、银基钎料对 Ti(C,N)基金属陶瓷与 4 5号钢进行钎焊试验。
3.
A trundled multi-station torch brazing machine is researched and developed for applying to the brazing of hydraulic accumulator in compressor .
研究开发了转盘式多工位自动火焰钎焊机 ,适用于压缩机储液器的大批量钎焊生产。
6) flame brazing
火焰钎焊
1.
By experimentation,comparison flame brazing's some limitations such as infiltration,working efficiency,working condition are poor and easy to burn out loop's insulating.
通过实验比较,阐述了气体火焰钎焊在焊接转子并头套时渗透率不高,生产效率低,生产环境差和容易烧坏线圈上的绝缘层等缺陷。
2.
The flame brazing technology for joining Al/Cu tube at middle-range temperature is realized.
采用火焰钎焊技术 ,实现了Al/Cu管异种材料的中温钎焊连接。
3.
By the measures of flame brazing,welding problems on aluminium alloy(LF6)and austenitic stainless steel(1Cr18Ni9Ti)are researched.
通过火焰钎焊的方法,实现铝合金(LF6)与奥氏体不锈钢(1Cr18Ni9Ti)的焊接。
补充资料：焦炉炭化室墙的火焰焊补
焦炉炭化室墙的火焰焊补
5矿。焦炉炭化窒墙蜘火嬲埠补
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条