1) refining ladle slag
精炼钢包渣
1.
The erosion of refining ladle slag for the synthetic MgOCaO refractory was studied by means of the high temperature microscope and petrographic analysis.
以轻烧镁粉和轻烧白云石粉为原料，合成镁钙砂并制砖；利用高温显微镜和岩相分析，将材料抗水化性与抗渣性结合起来，研究了精炼钢包渣对合成镁钙系耐火材料的侵蚀。
2) Ladle Refining Slag
钢包精炼渣
3) refining ladle
精炼钢包
1.
Experimental Study on Hot Simulation for Steel Temperature Rise in IR-UT-16 Refining Ladle;
IR－UT－16型精炼钢包吹氧升温热模拟试验
2.
The technical measures for increasing the service life of refining ladle lining were presented, and the influence of service conditions on the life during the campaign were investigated.
介绍了提高精炼钢包寿命的技术措施,对比了采用MgO-MA-C砖综合砌筑的试验方案A和采用优质MgO-C砖综合砌筑的试验方案B在精炼钢包中的使用效果,分析了不同工艺因素对钢包寿命的影响。
3.
The practice and effect about unshaped refractory used on the permanent layer of 100t refining ladle is introduced and a whole tamping process with automatic material flow without mold is given.
介绍了安钢第一炼轧厂100 t精炼钢包永久层耐火材料的材质选择及砌筑优化工艺,总结出一套适合该厂生产特点的钢包永久层整体打结工艺,采用无模具自流料打结钢包永久层,取得了良好的生产使用效果,提高了钢包永久层及钢包整体寿命,降低了耐火材料消耗,减少了穿包事故次数。
4) ladle refining
钢包精炼
1.
Physical model of 150t ladle refining process;
150t钢包精炼过程的物理模拟
2.
Research for Cold Roll Blank Forged by Ladle Refining Ingot;
钢包精炼锭锻制冷辊坯的研究
3.
In view of the role the ladle refining plays and its final goal the present paper describes the design of the alloy burdening model by means of the RBF network and verification of the model according to the data acquired from the practical refining operation and comparison with the results of the model prediction and shows the applicability of the RBF network in the model.
针对钢包精炼的作用及其最终目标要求,运用径向基(RBF)网络,对合金配料模型进行设计,并根据精炼实际数据对模型进行验证,然后与BP网络的预测结果进行比较,以显示径向基网络在精炼合金配料模型中的可行性。
5) Ladle Furnace
钢包精炼炉
1.
The harm from the harmonics of the ladle furnace and treatment of it;
钢包精炼炉的谐波危害及治理
2.
In accordance with such characters of the electrode control system in ladle furnace as the high non-linearity, time-variant, uncertainty of the model, output response time delay serious, and multivariable input and output coupling, an internal model control strategy based on real-time identification on line by neural network was presented.
针对钢包精炼炉电极控制系统具有非线性、时变、模型不确定、大滞后、多输入多输出耦合的特点,提出一种基于神经网络实时在线辩识的内模控制方案。
3.
By controlling refining slag composition, acid-soluble aluminium content in steel and argon blowing system during period of refining effectively, the average oxygen content of 50 ton ladle furnace of Laigang is only 18.
通过对精炼炉渣成分、钢中AlS含量以及精炼各期吹氩制度的有效控制,莱钢50t钢包精炼炉平均氧含量达到了18 1×10 6,达到了国外纯净钢标准水平。
6) Ladle Refining Furnace
钢包精炼炉
1.
Design ideas of computer monitoring and controlling system for ladle refining furnace;
钢包精炼炉微机监控系统的设计与实现
2.
SKF ladle refining furnace was introduced by No.
由于受设计时技术、资金的制约 ,马钢一钢厂从意大利 DANIEL I公司引进的 SKF钢包精炼炉 ,加热盖、真空盖等水冷设备在使用中 ,因工作环境恶劣造成的检修频率高、难度大 ,严重限制了生产能力的提高。
3.
The result of the experiment on refractories used for the 25t DC ladle refining furnace was summarized and the factors that influenced the ladle life were analyzed.
总结了安阳钢铁公司２５ｔ直流钢包精炼炉耐火材料实验结果并分析了影响钢包寿命的因素。
补充资料：LF钢包精炼炉(上海第五钢铁厂)
LF钢包精炼炉(上海第五钢铁厂)
谕LF钢包精炼炉(上海第五钢铁厂)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条