1) high stress impact wear
高应力冲击磨损
1.
The characteristics of microstructure changes and the formation and propagation of cracks on sample surface layer have been studied in this paper through high stress impact wear for bainitic steel.
研究了贝氏体钢经高应力冲击磨损后，试样表层内的组织变化及裂纹形成与扩展特征。
2) high-stress impact abrasion
高应力冲击磨料磨损
1.
Eutectic composition should be adopted for high-Cr white cast iron used under high-stress impact abrasion condition.
高应力冲击磨料磨损时,高铬白口铸铁应选共晶成分。
3) impact wear
冲击磨损
1.
The impact wear behavior of AZ91D magnesium alloys in de-ionized water;
AZ91D镁合金在水介质下的冲击磨损特性研究
2.
Study on Impact Wear Properties of Composite Layer with Tungsten and Chromium;
钨铬复合铸渗层的冲击磨损性能研究
3.
TiC_p Interfacial structure and impact wear resistance of TiC p/Ni coating by laser cladding;
激光熔覆涂层中TiC_p界面结构与涂层冲击磨损性能
4) impact abrasion
冲击磨损
1.
The impact abrasion performance of martensite steel was studied.
对马氏体细晶粒高强度钢的冲击磨损性能进行了研究。
2.
The impact abrasion properties of CrMnMo martensitic liner board steel and CrNiMo martensitic liner board steel were tested with MLDF-10 wear tester in acid-ironstone slurry.
采用MLDF-10冲击腐蚀磨损试验机研究了CrMnMo马氏体衬板钢和CrNiMo马氏体衬板钢在铁矿石酸性矿浆中的冲击磨损特性。
3.
The impact abrasion tests were performed,and both hardness and wear loss of the samples were compared with classical surfacing electrode D256.
经过对制备的试样分别进行多次冲击磨损试验,并与D256焊条进行对比试验,分析试样的硬度和磨损失重变化,结果表明,此种堆焊材料具有焊接工艺性好、堆焊层组织加工硬化率高和耐凿削式冲击磨损性能优异的特点。
5) high-stress abrasion
高应力磨料磨损
1.
Under high-stress abrasion condition,high-Cr white cast iron should contain enough amount of M7C3 carbides(more than 30%).
高应力磨料磨损时,高铬白口铸铁要具有足够量的M7C3碳化物(要大于30%),基体组织中马氏体要小于65%,残余奥氏体大于35%,奥氏体韧性高,对抵抗磨料的切向力有利,它在应力作用下,导致马氏体相变,使工作表面抗磨能力提高。
6) wear impact energy
磨损冲击功
补充资料：冲击高电压测量(见高电压测量)
冲击高电压测量(见高电压测量)
measurement of high impulse voltages
ch。门引才g。。dion丫日cel}o口g冲击高电压测量(rneasurement ofhighimpulsevoltages)见高电压测量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条