1) drillings temperature
钻屑温度
2) temperature of diamond bit
钻头温度
3) Drilling temperature
钻削温度
1.
Drilling temperature and its temperature distributing was studied using a thermal imaging device and it is indicated that the drilling heat is mainly produced from the friction between drilling bit backface and machind surface,and the higher the rotary rate,the higher the drilling temperature,and the higher the feedrate,the lower the drilling temperature.
利用热像仪对碳 /环氧复合材料高速钻孔时的钻削温度及温度场分布进行了系统的试验研究。
2.
Experience formulas were developed to predict drilling torque,thrust force and drilling temperature with multiple linear regression analysis model.
为了得到钻头直径与钻削参数对钻削力和钻削温度的影响规律,故用高速钢标准钻头对1Cr18Ni9Ti与45钢进行了钻削对比试验,并用多元线性回归模型建立了钻削力和钻削温度的经验公式。
3.
Applying to the LabVIEW development platform and combining with ADLINK PCI-9118 data acquisition modules,a drilling temperature Dynamic measurement system by semi-manual thermocouple method is designed,It concludes the data acquisition,data processing,data analysis,data storage and so on.
介绍了一种基于LabVIEW开发平台与凌华PCI-9118数据采集卡相结合,并以半人工热电偶法为测温方法的钻削温度动态测试系统,具有数字及图形显示、数据存储、数据回放、数据处理等功能。
4) drilling sludge
钻屑
1.
The blasting effect was checking using sight instrument, electromagnetic emission (EME) technique and drilling sludge methods.
采用矿用钻孔窥视仪并配合电磁辐射法和钻屑法对爆破进行了效果检验。
2.
This paper discusses anew method of caculating critical rotational speed on the basis of studying the transportation rule of long screw drilling sludge and points out that critical rotational speed changesradially along the blade,and it is the function of feed speed.
作者在研究长螺旋钻进钻屑运移规律的基础上，建立了新的临界转速计算方法，指出临界转速沿叶片径向是变化的，并且是给进速度的函数。
5) drilling cutting
钻屑
1.
The solidification treatment of drilling cutting and waste drilling fluid is a major research subject on harmless treatment of waste from drilling at present.
钻屑和废钻井液的固化处理是现阶段钻井废物无害化处理的主要研究方向,研究利用固化剂对钻屑和废泥浆进行固化处理,优选配方(水泥+粉煤灰+添加剂)进行固化处理;同时考查了钻屑、钻井液固化填埋后对周围环境的影响。
2.
A simple laboratory testing method is established,and by means of this method mechanical bond strength is tested between drilling cutting and oilwell cement rock.
在实验室内，模拟水泥环与地层胶结全过程，分析了泥饼以及采用不同配方的水泥浆，对各种钻屑与油井水泥胶结强度的影响。
3.
In this thesis,several kinds of solidification agent have been screened by a lot of experiments,which are suitable for drilling cutting and waste drilling mud with high density(ρ>2.
通过大量实验研究,筛选出了分别适合于钻屑与高密度(ρ>2。
6) drilling cuttings
钻屑
1.
Durand formula,critical flow rate increased with the increase of the granularity of wellhead drilling cuttings and the volume concentration of liquid discharged when the structure of equipments were determined.
Durand临界流速计算公式分析得出,在设备结构确定以后,排料临界流速随着井口钻屑粒径、排料流体体积分数的增加而增加。
2.
A new machine of medel GZS7 is invented to convey the drilling cuttings.
采用逐点张力法对钻屑输送机所用链条各部位的受力情况进行了分析，给出了钻屑输送机所用链条的张力计算公式，为校核链条的强度及计算钻屑输送机所需功率提供了依据。
补充资料：滴屑屑
1.颤抖貌。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条