1) fire technology characteristic
着火工艺特性
2) ignition characteristics
着火特性
1.
Experimental study on ignition characteristics of typical construction and upholstery wood;
典型建筑装潢板材的着火特性实验研究
2.
Study on ignition characteristics of micro-pulverized coal by thermogravimetry;
超细煤粉着火特性的热重分析
3.
On a pressurized thermogravimetric analytical device of single-furnace and double sample bucket structure a relatively systematic experimental and theoretical study was conducted of the ignition characteristics and combustion stability of gasified semi-char under an elevated pressure.
在单炉膛双吊蓝加压热重分析仪上对气化半焦的加压着火特性和燃烧稳定性进行了较为系统的试验和理论研究,考察了半焦种类、总压、氧浓度、粒径和加热速率等因素对半焦着火特性和燃烧稳定性的影响规律,并以纯碳测试数据为基准,提出了燃烧稳定性的判别指数Rw。
3) firing behavior
着火特性
1.
Cold start firing behavior of electronically controlled injection methanol engine with LPG as ignition improver;
电控喷射甲醇发动机掺烧液化石油气的冷起动着火特性
2.
Effect of preheating on firing behavior of an electronically controlled injection methanol engine during cold start;
预热对电控喷射甲醇发动机冷起动着火特性的影响
3.
The transient firing behavior of a spark-ignition engine fueled with gasoline,liquid petroleum gas(LPG) and methanol respectively during cold start was investigated experimentally by means of cycle-by-cycle control strategy on a 125 mL-single-cylinder four-stroke electronically controlled fuel injection engine.
基于循环控制策略,在一台125 mL单缸四行程电控喷射点燃式发动机上,分别燃用汽油、LPG和甲醇3种燃料进行了冷起动瞬态工况着火特性的试验研究。
4) ignition characteristic
着火特性
1.
The ignition characteristic of husk was obtained by TG.
通过热重分析得到稻壳的着火特性。
2.
This paper studies the ignition characteristic of 7 coals in the laboratory scale fluidized bed heated by the hot gas under distributor.
在电加热的小型流化床燃烧系统上,采用热烟气炉下点火方式研究了7个煤种的着火点,并分析了粒径、床温、挥发分、水分等因素对着火特性的影响。
3.
The ignition characteristic of Fujian Longyan anthracite was investigated.
测定了福建龙岩无烟煤的着火特性 ,分析了粒径、床温对着火点的影响 。
5) technological characteristic
工艺特性
1.
Metal transfer and technological characteristic of typical titanium flux-cored wires at home and abroad;
国内外典型药芯焊丝的熔滴过渡及其工艺特性
2.
The stucture, mixing principle and mixing technological characteristics of new tenon type rotor with multi-rhombus were studied.
研究了新型多棱榫状转子的结构、混炼原理和工艺特性。
3.
Based on the analysis on technological characteristic of PMMA materials,the technological requirements in designing products and injection mould for PMMA materials were discussed in deˉtails.
在对PMMA材料工艺特性的分析及阐述的基础上,重点分析PMMA在制品设计、模具设计中的工艺要求,并分析其制品在注射成型生产中的工艺方法和特点。
补充资料：PC/ABS塑料特性、成型工艺、用途
PC/ABS 聚碳酸酯和丙烯腈-丁二烯-苯乙烯共聚物和混合物
典型应用范围:计算机和商业机器壳体、电器设备、草坪园艺机器、汽车零件仪表板、内部装修以及车轮盖）。
注塑模工艺条件:干燥处理：加工前的干燥处理是必须的。湿度应小于0.04%，建议干燥条件为90~110℃，2~4小时。熔化温度： 230~300℃。模具温度：50~100℃。注射压力：取决于塑件。注射速度：尽可能地高。
化学和物理特性: PC/ABS具有PC和ABS两者的综合特性。例如ABS的易加工特性和PC的优良机械特性和热稳定性。二者的比率将影响PC/ABS材料的热稳定性。PC/ABS这种混合材料还显示了优异的流动特性。
典型应用范围:计算机和商业机器壳体、电器设备、草坪园艺机器、汽车零件仪表板、内部装修以及车轮盖）。
注塑模工艺条件:干燥处理：加工前的干燥处理是必须的。湿度应小于0.04%，建议干燥条件为90~110℃，2~4小时。熔化温度： 230~300℃。模具温度：50~100℃。注射压力：取决于塑件。注射速度：尽可能地高。
化学和物理特性: PC/ABS具有PC和ABS两者的综合特性。例如ABS的易加工特性和PC的优良机械特性和热稳定性。二者的比率将影响PC/ABS材料的热稳定性。PC/ABS这种混合材料还显示了优异的流动特性。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条