1) abrasive
研磨料
1.
The crystallization-resistant phthalocyanines BGS pigment were produced,through the choice of surface active agent and abrasive ratio test.
通过选择表面活性剂试验和研磨料配比试验，生产出了抗结晶的酞菁蓝ＢＧＳ颜料，并介绍了在长期生产实践中总结出的经验和体会。
2) nano-abrasive
纳米研磨料
1.
For chemical mechanical polishing of ILD(Interlevel Dielectric) in ULSI, the silica sol nano-abrasive with large particle was strongly required because of lower polishing rate.
以低分散度硅溶胶纳米研磨料配制抛光浆料进行了二氧化硅介质的 CMP研究 ,结果表明 ,平均粒径 1 0 3 。
3) grinding
研磨
1.
Fractal model for particle-size distribution of coal grinding;
基于分形方法的煤炭研磨颗粒粒度分布模型
2.
Preparation of γ-Fe_2O_3 Nanoparticles by Solid(wet)-phase Grinding;
γ-Fe_2O_3纳米粒子的(湿)固相研磨法制备研究
3.
The grinding materials and technology for stainless steel;
不锈钢研磨材料及研磨工艺
4) Lapping
研磨
1.
Rapid detection of subsurface damage of optical materials in lapping process and its influence regularity;
光学材料研磨亚表面损伤的快速检测及其影响规律
2.
Research on high speed lapping paraboloid workpiece based on bending and forming method;
基于弯曲成形法抛物面高速研磨的研究
3.
Research on the Lapping Uniformity of Uncertain Eccentricity Plane Lapping;
不定偏心平面研磨均匀性的研究
5) polishing
研磨
1.
Polishing Robot System and the Control of Its Motion;
研磨机器人系统及其运动控制
2.
A new way of polishing is discussed, in which the ultrasonic energy is applied to the interface of mechanical polishing and correlative equipment and experimental equipment are designed.
为了提高光纤连接器端面的加工效率和加工质量,改善连接器光传输性能,探讨了在机械研磨的界面上引入超声能的复合研磨方式,设计了相应的超声机械研磨装置。
3.
To improve the material removal rate(MRR),this paper discussed a new ultrasonic polishing in which the ultrasonic energy was introduced to the interface of common polishing,and compared this new polishing process with the common polishing process in the MRR.
为了提高机械研磨的材料去除率,探讨了在机械研磨的界面上引入超声能的复合研磨方式,将机械研磨和引入超声的复合研磨两种方法的去除效率进行了实验对比;发现复合研磨后,去除效率有显著提高;得出超声/机械复合研磨的加工效率明显优于机械研磨。
6) grind
研磨
1.
Siemens S7-300 PIc In Paper making Grinding Production Line Application;
西门子S7-300 PLC在造纸研磨生产线中的应用
2.
The applications of the different grinding media in the grind of ink were summarized in this pa- per.
介绍不同的研磨介质在油墨中的应用,并讨论了研磨介质的种类,体积比及尺寸对基料细度的影响。
3.
The grind renovation processes of rough grind,fine grind and polishing are analyzed.
介绍拉丝模模坯、模套的加工及模芯装镶过程中应注意的要点 ;给出拉丝模修复常用研磨剂的特性和应用范围 ,比较了几种研磨剂研磨效率 ;分析粗磨、细磨和精磨、抛光的研磨修复工
参考词条
补充资料：料料窕窕
1.形容人的身材过于瘦长。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。