说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 对版误差
1)  error disposition
对版误差
1.
The error disposition was obtained when the images of online printed products were obtained from the production line and rectified by the servomonitor
介绍一种凹版印刷机计算机图像检测和位置控制系统,利用彩色边缘检测等方法对在线印刷品的图像进行实时图像处理和分析,可动态或静态显示在线印刷品图像,并得到与产品图像质量相关的参数,以此检测产品的质量;并利用各色之间的对版误差,通过伺服电机进行实时位置校正。
2)  relative error
相对误差
1.
Linear combination forecast based on relative error criterion;
基于相对误差的线性组合预测研究
2.
The model is used to analyze the relative error of forecast and to forecast the exploitable geological ore reserves of Miaogou Mine in 2007.
通过运用数理统计中的回归分析方法确立采出矿石地质矿量预测数学模型,分析预测相对误差,并对2007年采出矿石地质矿量进行预测。
3.
The calculation methods of pH and relative error were studied in different acid-base solution.
根据相对误差的要求,研究不同酸碱平衡溶液中pH值的计算方法,并根据酸碱的强弱和浓度及离解常数的大小,进行近似处理,可得到简便计算pH值的公式。
3)  error in positioning and tool-setting
对定误差
4)  absolute error
绝对误差
1.
By comparison with the results of ideal Henon sequence mixed with noise,the improved Farmer algorithm is able to increase the precision of noise attenuation and reduce the absolute error between itself and ideal Henon sequ.
通过对混有噪声的Henon序列进行仿真实验,仿真结果显示,改进后的Farm er算法能够提高噪声衰减的精度,降低与理想Henon序列的绝对误差。
2.
According to original laser measure error and error analysis transfer expressions,calculations about absolute errors and relative errors of the measuring deformation of wing were performed.
以激光器的原始测距误差为出发点,依据误差传递公式,分析了测量机翼变形量的绝对误差和相对误差,并给出了计算仿真结果和相应的图形。
3.
It may measure the frequency and phase of the signal which begin from 10 Hz to 20 kHz,absolute error isn′t more than 1°.
可以对10 Hz~2 0 k Hz频率范围的信号进行频率、相位等参数的精确测量,测相绝对误差不大于1°;采用数码管显示被测信号的频率、相位差。
5)  tool clamping error
对刀误差
1.
Based on the analysis of the influence of actual distribution of manufacturing deviation and fit-up gap on tool clamping error of driller clamping fixture, the analytic method about the tool clamping error is put forward.
通过分析钻床夹具制造偏差的实际分布状态与装配间隙 (过盈为非间隙 )对对刀误差的影响 ,提出了对刀误差的实态分析计算方法。
6)  Alignment Error
对准误差
1.
The Hazard and It's Correcting Methods of Alignment Error between Tool-tip and Spindle Center of NC Lathe;
数控车床刀尖与主轴中心对准误差的危害及纠正方法
2.
Observability and alignment error analysis for rapid transfer alignment of inertial navigation system;
惯导快速传递对准的可观测性和对准误差分析
3.
Analysis of system servo following error caused by alignment error of ESG;
静电陀螺仪对准误差产生的系统伺服随动误差分析
补充资料:版版
1.邪僻;反常。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条