1) variable cross-section rolling forming
变值轧制成型
1.
The variable data rolling forming that is variable cross-section rolling forming, is a new technological method which has a bright future in the building technique, using the rolling method to produce work-pieces or semi-finished products.
变值轧制成型是采用轧制的方式制造零件或毛坯的工艺方法 ,是一种新兴的有发展前途的制造技术。
2) rolling modeling
轧制成型
1.
the changing law of unit rolling pressure, spread,forward slip value and reducing rate is showed which is helpful for technological design of rolling modeling of cored welding strip in theory.
以典型的矩形断面形状药芯焊带成型过程为研究对象 ,通过实验测试 ,得出了成型时单位轧制压力、宽展、前滑值与压下率之间的变化规律 ,为药芯焊带轧制成型工艺设计提供了理论指
3) rolling formation
轧膜成型
4) Shaping Roller
成型轧辊
1.
The Finishing of Shaping Roller by Pulse Electrochemical Technology
成型轧辊表面的脉冲电化学光整加工技术研究
5) rolling
[英]['rəʊlɪŋ] [美]['rolɪŋ]
轧制成形
1.
The law of main technological parameters with relative reduction is showed which is helpful for technological design of rolling of cored welding strip in theory.
以典型的矩形断面形状药芯焊带轧制成形过程为研究对象,通过实验测试,得出了成形时主要工艺参数与相对压下量之间的变化规律,为药芯焊带轧制成形工艺设计提供了理论指导。
2.
The influence of the lubricating film in the deformed zone on the rolled stainless steel surface roughness was studied in cold rolling stainless steel strips.
采用不同粘度的冷轧油实现不锈钢轧制成形过程中的润滑,研究了轧制变形区润滑油膜性能对轧制不锈钢表面粗糙度的影响,并进一步分析了润滑油膜在轧制成形过程中的作用及油膜形成机制。
6) rolling deformation
轧制变形
1.
The influence of rolling deformation and heat treatment temperature on structures, mechanical properties is studied.
X射线衍射结果表明,随着轧制变形量的增加,Ti50Ni47Fe3合金在轧制方向上出现了择优取向;Ti50Ni47Fe3合金的晶粒尺寸随着轧制变形量的增加而减小,随着热处理温度的升高而增大;Ti50Ni47Fe3合金的抗拉强度和屈服强度随着轧制变形量的增加而增大,随热处理温度的升高而降低。
2.
The results show that the orientation distribution calculated by the FC (full constraints)Taylor model is closer to experimental results than those by other models at the low rolling deformation de.
结果表明:在低轧制变形程度时,完全限制(FC)模型计算结果的取向分布较其它模型更符合实际结果。
3.
The results show that the rolling textures for the sample with initial randomly distributed texture mainly consists of C,S and B components during rolling deformation while the orientation density values for the three textures only have slight difference, most crystallites a.
结果表明:随着轧制变形的进行,对于初始自由分布的样品,晶粒取向主要向α,β取向线附近聚集,其形变织构主要由C,S及B织构组成,且3种织构成分密度值相差不大;对于初始具有近似立方织构的样品,晶粒取向主要向β取向线上聚集,其形变织构主要由C,S织构组成,B织构成分相对较弱。
补充资料：板带轧制速度规程(见板带轧制规程设计)
板带轧制速度规程(见板带轧制规程设计)
speed schedule for plate and strip rolling
bandai zhazhi sudu guieheng板带轧制速度规程(speed seheduxe fo:plateand strip rolling)见板带札制规程设计。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条