1) flexural rigidity modulus
弯曲刚度系数
2) bending rigidity
弯曲刚度
1.
Discussion on bending rigidity anisotropy of fabrics;
织物弯曲刚度各向异性探讨
2.
Bending deformation and bending rigidity of mechanical components;
机械构件的弯曲变形与弯曲刚度
3.
Approach to calculating bending rigidity of rubber-reinforced track of tractors and its experimental verification;
拖拉机橡胶钢筋履带弯曲刚度计算方法与试验验证
3) bending stiffness
弯曲刚度
1.
Applied investigation on the effects of bending stiffness of machine bed's simulating parts on its thermal geometrical precision;
机床床身模拟件的弯曲刚度对其热态几何精度影响规律的应用研究
2.
Analysing parameters of bending stiffness of FRP and designing its structure;
FRP弯曲刚度的参数分析与结构设计
3.
Engineering algorithm on bending stiffness of elastic rubber bushing of car suspension;
轿车悬架弹性橡胶衬套弯曲刚度的工程算法
4) Bend stiffness
弯曲刚度
1.
The mechanical models of bend stiffness and bend strength of the pallets girder and deck were established.
通过分析木托盘在均布载荷作用下的受力变形情况,建立了木托盘梁和铺板的弯曲强度和弯曲刚度的力学模型,提出了托盘弯曲强度和刚度的条件。
5) flexural stiffness
弯曲刚度
1.
The relationship between axial stiffness, torsional stiffness, flexural stiffness and deformation has been given.
通过非线性有限元方法对橡胶-钢球支座在轴向拉伸、扭转和弯曲的大变形载荷作用下的力学行为进行分析,得出支座的轴向刚度、扭转刚度和弯曲刚度与变形的关系。
2.
Based on the bifurcation buckling of abnormal beamcolumn steel frame,it was found that the way to ascertain column s effective length of normal steel frame can also be used in abnormal beam-column steel frame;the principle of virtual work was used to deduce the flexural stiffness of two kinds of Abnormal beams,and its effect on the effective length of rigid steel frame column was analyzed.
运用虚功原理推导了两种典型的非规则梁的弯曲刚度,并分析了其对钢框架柱计算长度的影响。
6) flexural rigidity
弯曲刚度
1.
One of the key problems of this technique,such as flexural rigidity of the RC beams strengthened with CFL,must be discussed.
1,ISIS M03-01和GB 50010,结合静载和疲劳试验,探讨了CFL增强RC梁弯曲刚度的变化规律和计算方法。
2.
Static test of eight steel-light weight concrete composite beams with re-entrant trough profiled steel sheeting specimens were conducted to study the flexural rigidity of the composite beams.
完成了8个钢-闭口型压型钢板轻骨料混凝土组合梁试件的静力试验,对组合梁弯曲刚度计算方法进行研究。
3.
Based on the flexural rigidity of curve box girder,This paper proposes the concept of equivalent span,and transforms the space analysis of continuous curve box girder into the foree analysis of plaae structure.
根据曲梁的弯曲刚度，提出了等代跨长的概念，并将连续曲梁桥的空间分析转化为平面杆系结构的内力分析。
补充资料：轧机刚度系数
轧机刚度系数
rigidity coefficient of rolling mill
zhalj gongdu xishu轧机刚度系数(rigidity eoeffieient of rollingmill)使轧机产生纵向单位弹性变形所需施加的轧制力。其几何意义为轧机弹性曲线直线段的斜率，记作 dP K~~共气 “m ds式中d尸为轧制力增量;ds为辊缝增量;Km为轧机刚度系数，其量纲为kN/mm。因此，某一轧机的刚度系数可根据轧机的弹性曲线的斜率计算确定。实际上，由于轧制时轧棍和整个车L机在负荷作用下温度升高，辊缝发生变化而成为一个变值，轧辊的圆度和安装偏差会造成轧件的纵向厚度偏差呈高频周期性变化，轧件、一公淤叮派李点- 翻~香爪~~咋今粉~ 轧钢机按机架排列分类 a一单机架;吞一横列式;一顺列式;d一棋盘式;~半连续式;了一连续式宽度也会影响轧辊的弯曲弹性变形等，所以为了提高轧件厚度控制的精确度，轧机的刚度系数一般都通过现场实测方法得到。但也可以在用解析方法分别算出轧辊的刚度系数K，、机架的刚度系数KZ、安全臼的刚度系数K3、压力传感器的刚度系数K4等之后，按下式计算 1 K，~— 1 .1 .1 .1 分+分十含+亡 K:1 KZ’K3’K4因此，K。又称等效刚度。 (赵以相)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条