1) accumulative roll bonding(ARB)
累积复合轧制
1.
Experiments were conducted to investigate the effect of grain refining mechanism on the microstructure and mechanical properties of 1060 commercially pure aluminum in accumulative roll bonding(ARB),in which two kinds of routes,Route A and Route B,were employed.
采用累积复合轧制(ARB)技术的两种工艺路径,研究变形后1060工业纯铝的显微组织和力学性能变化。
2) accumulative roll bonding
累积轧合法
1.
accumulative roll bonding, equal channel angular pressing, and high pressure and torsion, as well as the characteristics, present state and perspectives of SPD are summarized in this paper.
通过介绍累积轧合法、等通道角挤压法和高压扭转法等3种目前最主要的深度塑性变形方法,分析了深度塑性变形法的特点和现状,并对其未来进行了展望。
3) Accumulating Reproducer
累积复制器
4) roll-bonding
轧制复合
1.
The technology of roll-bonding was applied to prepare the foaming precursor in this paper.
将轧制复合工艺应用于发泡预制体的制备,研究了粉末致密化过程与面板/芯层的结合机制。
2.
Author studied the production technology of aluminum foam sandwich prepared by roll-bonding/powder metallurgy foaming process in this paper,and analyzed the effect of main technological conditions on foaming structure of sandwich layer,and optimum technological parameters were finally obtained.
研究了采用轧制复合-粉末冶金发泡法制备的泡沫铝夹心板的生产工艺,探讨了主要工艺条件对芯层泡沫结构的影响,得到了优化的工艺参数。
3.
The dynamic temperature field during roll-bonding combined with high-frequency alternating current heating has been numerically simulated by a simplified model.
通过数值模拟获得了高频加热-轧制复合过程中的动态温度场。
5) sandwich rolling
复合轧制
1.
A powder-A1 plate sandwich rolling processing is proposed for preparation of aluminum alloy foam sandwich with a metallurgy bonding interface.
通过粉末-铝板复合轧制方法制备出一种界面为冶金结合的泡沫铝夹芯板。
2.
The foam aluminum sandwich panels with metallurgy bonding interface are prepared by the sandwich rolling method,the two Al face-sheets are stacked and mixed powders with foam agent are put between them,which are sandwich rolled and a foaming precursor is obtained,then it is foamed in heating furnace.
采用复合轧制的方法,即将带有发泡剂的混合粉末置于两铝面板之间进行复合轧制使之成为预制发泡体,然后再在炉中发泡的方法,制备界面为冶金结合的泡沫铝夹芯板,通过摆锤冲击实验,研究界面为冶金结合的泡沫铝夹芯板与胶接夹芯板的冲击性能的区别。
6) Composite rolling
复合轧制
1.
surface processing+composite rolling+heat treatment were carried out.
进行了钢-铜、钢-铝冷轧复合实验,即表面处理+复合轧制+轧后热处理。
2.
By the experiment of rolling stop,on the basis of analying the law of the composite rolling deformation of the double metals,the article derives the theoretical formulation of calculation of layer thickness ratio on the composite material of the double metals,and the error is less than 5% according to the check by the results of actual test.
通过轧卡实验，在分析双金属复合轧制变形规律的基础上，推导出了双金属复合材料厚比计算的理论模型。
3.
The principle of layer thichness ratio is studied experimentally in the process of Al-steel composite rolling and the formulation of rolling force was established.
用实验方法研究了铝－钢双金属复合轧制时层厚比的变化规律。
补充资料：板带轧制速度规程(见板带轧制规程设计)
板带轧制速度规程(见板带轧制规程设计)
speed schedule for plate and strip rolling
bandai zhazhi sudu guieheng板带轧制速度规程(speed seheduxe fo:plateand strip rolling)见板带札制规程设计。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条