1) melt viscosity
熔融黏度
2) melt viscosity
熔体黏度
1.
The relationships of the melt viscosity,the surface tension,foamer and temperature were theoretically analyzed.
讨论了泡沫铝制备过程中温度的影响,理论上分析了温度与熔体黏度、表面张力和发泡剂的关系,并通过实验探讨温度对泡沫铝孔结构和孔隙率的影响。
2.
The results showed that the melt viscosity and decomposition of TiH_2 are the two predominant factors on which the bubble stability depends.
采用在铝硅合金粉末中加钙来增加熔体黏度,控制熔体的表面张力;通过控制氢化钛加入量来控制氢化钛分解释放出氢气的量;控制发泡时间,使发泡在气泡的稳定时段内进行;保持气泡内气体压力与气泡表面张力的平衡,可获得孔结构均匀、密度适合的泡沫铝材料。
3) fusion temperature
熔融温度
1.
An in-depth study was conducted concerning the fusion temperature and fusion process dynamic characteristics of three representative pairs of ash samples taken from two units of coal water slurry (CWS)-fired boilers.
对取自2台水煤浆锅炉3对各具代表性灰的熔融温度和熔融过程动态特性进行了深入研究。
2.
Plenty of medical glass bottles which were present in medical wastes had rather low fusion temperatures.
实验结果显示,不同化学组分对熔融温度有不同的影响,SiO2能够提高医用玻璃的熔融温度,B2O3和碱金属氧化物(Na2O、K2O)会大幅降低医用玻璃的熔融温度,而碱土金属氧化物(CaO、BaO)和Al2O3会使医用玻璃的软化温度升高,却能使流动温度降低。
5) melting temperature
熔融温度
1.
The melting characteristics and behavior of heavy metals of fly ashes were investigated under different melting temperatures.
对城市垃圾与煤混烧飞灰进行旋风熔融试验,分析了不同熔融温度条件下熔渣的微观形貌及重金属行为。
2.
The influence of fly ash on partition characteristics of heavy metals before and after melting treatment was studied , including the melting temperature, melting time and the basicity.
研究探讨了熔融温度、熔融时间、碱基度对飞灰熔融处理前后重金属分布特性的影响。
3.
The melting temperature,melting heat,static and dynamic mechanical properties of PA6/PTFE blends and PA66/PTFE blends are experimentally investigated in this paper.
PA6/PTFE共混物的熔融温度随PTFE含量的增加而升高,熔融热却随PTFE含量的增加而降低。
6) melting point
熔融温度
1.
As irradiation dose increases, the gel content and charpy impact strength increases, whereas crystallinity, melting point and elongation at break decreases.
结果表明 :在 0～ 30 0 k Gy的辐射剂量范围内 ,限定量的氧对 HDPE的性能并无太大的影响 ,HDPE的凝胶含量和缺口冲击强度随辐射剂量的增加而增加 ,但结晶度、熔融温度和断裂伸长率却随剂量的增加而下降。
2.
By co polymerization between a flexible co-monomer and acrylonitrile reduces the melting point or increases the decomposition temperature in order to produce melt processable resin.
8℃,而熔融温度仅为188。
补充资料：熔融黏度
分子式：
CAS号：
性质：又称熔体黏度。高分子聚合物熔体和黏度。与聚合物分子结构和聚合度有关，并随温度、压力、剪切速度的变化而异。
CAS号：
性质：又称熔体黏度。高分子聚合物熔体和黏度。与聚合物分子结构和聚合度有关，并随温度、压力、剪切速度的变化而异。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条