说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 齿尖圆弧半径
1)  tip circular-arc radius
齿尖圆弧半径
2)  knife point circular arc radius
刀尖圆弧半径
1.
Influence of knife point circular arc radius to circular cone parts processing precision;
刀尖圆弧半径对圆锥零件加工精度的影响
3)  corner radius
刀尖圆弧半径
1.
The corner radius has great influence to the precision of work pieces machined on a numerical control (NC) lathe.
刀尖圆弧半径对数控车床加工零件的精度有很大影响,如果只按零件的加工形状编制加工程序,则有时零件不合格,特别是在加工带有锥面和圆弧的零件时,常常相差较大。
2.
The influence of the corner radius on the spherical parts processing precision in the numerical control turning process is analyzed.
分析了数控车削加工中刀具刀尖圆弧半径对球面零件加工精度的影响,并提出相应措施,为正确编制加工程序、选择加工工艺和刀具参数提供了依据,提高了零件加工精度。
3.
This paper is mainly on how to remove inaccuracy by compensating the corner radius.
主要讨论怎样用刀尖圆弧半径补偿功能来消除误差。
4)  radius of the cutter tip
刀尖圆弧半径
1.
It analyzes the effects on the production quality caused by the factors including the types of the cutters, the radius of the cutter tip, the error of the cutter center elevation and so on, on the basis of which some corresponding measures were presented.
对数控车削中使用的刀具类型及其选用方法作了介绍,并就刀具的类型、刀尖圆弧半径、刀具中心高误差等因素对加工品质的影响作了分析,并在此基础上提出了应对措施。
2.
The paper introduces the types of cutting tools used in NC producing and the way of selecting them,and analyzes the effects of some factors,such as the types of the cutters and the radius of the cutter tip,on the producing quality.
对数控车削中使用的刀具类型及其选用方法作了介绍,并就刀具的类型、刀尖圆弧半径对车削质量的影响作了分析,并针对影响工件加工质量的因素提出了相应对策。
5)  tip arc-radius
尖角圆弧半径
1.
Then, the machined V-shaped groove was measured by a 3D laser meter to compare its profile,and the evaluation mode of the shape error PV and tip arc-radius of the V-shaped groove was established.
依靠单晶金刚石的锋锐刃角在光学玻璃上进行V槽的微纳尺度切削试验,利用3D激光超精密检测仪器检测加工的V切痕,构建了微V槽切痕的形貌图,并建立了V槽形状误差PV值和V槽尖角圆弧半径的评价模式。
6)  tool nose radius
刀尖圆弧半径
1.
In the process of CNC lathe machining,programming such as the ideal tool corner,in the parts of the cone and the arc of processing,often appear the processing error,it is mainly due to the existence of tool nose radius of a workpiece processing error.
数控车加工中,如按理想刀尖进行编程,在对零件的锥面和圆弧加工时,经常会出现加工误差,这主要是由于车刀刀尖圆弧半径的存在对工件加工产生了误差。
补充资料:利用小半径模具弯制大半径管件
高档汽车座椅因座椅形状需要,其骨架通常有3维大半径复合圆弧,作为生产汽车座椅的专业厂,我们常有这样的零件要加工。
  安徽淝河客车厂凯斯鲍尔豪华客车座椅靠背骨架,成型圆弧较大,有4种弯曲半径,且有3维复合弯,我们手头有的精密弯管设备-美国伊顿伦纳德公司的矢量弯管机VB200HP只能弯制弯曲半径203.2mm以内的管件。
  如何利用弯管机弯出这样的大半径3维复合弯?我们分析了零件的特性:形状要正确,但由于骨架是包裹在护面和海绵软垫之中的,零件不外露。因此采取了将大半径圆弧分解为多个小半径圆弧与多段直线依次相连的方法,近似地获得所需形状。首先将其分段,将各大圆弧作成多段55mm长的直线相连的折线,计算出各交点坐标,然后用恰当半径的圆弧结合旋转度将相邻线段连接,形成近似的大半径圆弧。这样产生的新的管件符合VB200HP弯管机的加工条件,同时由于有较多点的坐标与原设计一致,分段弯曲造成的过渡不流畅由于零件的装配隐蔽性而显得无关紧要。
  实践中,我们在对管件实样分段划线的基础上采用美国伊顿伦纳德公司的另一台设备-VECTOR 1 S4XL激光测量机,通过对每一分段测2点的方法,获取圆弧近似折线的交点坐标,进而转换成弯管程序弯制管件。表1为该零件的坐标,表2为该零件的弯管程序(注:L为直线段长度,R为旋转度,A为弯曲角度)。
  进而,我们可以把这种方法应用到其他类似方面-只要是隐蔽的或者是非装饰性的还有试制的弯管,都可以采用本文所述方法。这样,许多原来不能用VB200HP弯管机弯制或难以弯制的管件,现在都能轻而易举地制造出来了。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条