1) sector bevel gear
扇形圆锥齿轮
2) a sector of a sphere
扇形圆锥
3) bevel gear
圆锥齿轮
1.
Design of bevel gear forgings and Developing of SolidWorks;
基于Solid Works的圆锥齿轮精锻件的二次开发
2.
Optical design of flashed cold die forging of car used bevel gear;
轿车圆锥齿轮闭式冷精锻凹模的优化设计
3.
Simulation and creating model of straight bevel gear;
直齿圆锥齿轮的建模和运动仿真
4) cone gear
圆锥齿轮
1.
The Adjustment for the Clearance of the Helix Cone Gear Mesh Side for the Reducer and the Clearance of Paired Cone Roller Bearings;
减速机螺旋圆锥齿轮啮合侧间隙及成对圆锥滚子轴承间隙调整
2.
The influence of the load distributing in the tooth direction and the superposition degree of cone gear on the transmission;
圆锥齿轮的齿向载荷分布和重合度对传动的影响
3.
Measures to control heat treatment distortion of the cone gears were tested and analyzed.
对如何控制圆锥齿轮热处理畸变进行了试验和分析 ,结果表明 ,通过改变装炉的方式、淬火方法和控制冷却 ,能有效地控制齿轮的畸变 ,解决了生产中的关键问
5) sector gear
扇形齿轮
1.
A sector gear and rack mechanism is adopted in the mould for side circular arc corn pulling of the faucet castings, at the time, the corns pulling of the faucet castings in other two direction are respectively finished by the correspo.
该模具采用扇形齿轮-齿条机构实现龙头体铸件的侧向圆弧分型抽芯,同时通过相应的两套斜销滑块机构分别实现龙头体铸件另外两个方向的侧向分型抽芯。
6) toothed segment
齿轮扇形
补充资料：55°圆锥管螺纹型式和尺寸
| 螺纹代号 | 基本尺寸 英 寸 | 大径 mm d=D | 螺距 mm p | 每英寸牙数 tpi | 中径 mm d2=D2 | 小径 外螺纹 d3 | 牙型高度 H1 | 圆弧尺寸 r | 底孔尺寸 mm |
| R 1/16 | 1/16＂ | 7.723 | 0.907 | 28 | 7.142 | 6.561 | 0.581 | 0.125 | 6.4 |
| R 1/8 | 1/8＂ | 9.728 | 0.907 | 28 | 9.147 | 8.566 | 0.581 | 0.125 | 8.4 |
| R 1/4 | 1/4＂ | 13.157 | 1.337 | 19 | 12.301 | 11.445 | 0.856 | 0.184 | 11.2 |
| R 3/8 | 3/8＂ | 16.662 | 1.337 | 19 | 15.806 | 14.950 | 0.856 | 0.184 | 14.75 |
| R 1/2 | 1/2＂ | 20.955 | 1.814 | 14 | 19.793 | 18.631 | 1.162 | 0.249 | 18.25 |
| R 3/4 | 3/4＂ | 26.441 | 1.814 | 14 | 25.279 | 24.117 | 1.162 | 0.249 | 23.75 |
| R 1 | 1＂ | 33.249 | 2.309 | 11 | 31.77 | 30.291 | 1.479 | 0.317 | 30 |
| R 1 1/4 | 1 1/4＂ | 41.910 | 2.309 | 11 | 40.431 | 38.952 | 1.479 | 0.317 | 38.5 |
| R 1 1/2 | 1 1/2＂ | 47.803 | 2.309 | 11 | 46.324 | 44.845 | 1.479 | 0.317 | 44.5 |
| R 2 | 2＂ | 59.614 | 2.309 | 11 | 58.135 | 56.656 | 1.479 | 0.317 | 56 |
| R 2 1/2 | 2 1/2＂ | 75.184 | 2.309 | 11 | 73.705 | 72.226 | 1.479 | 0.317 | 71 |
| R 3 | 3＂ | 87.884 | 2.309 | 11 | 86.405 | 84.926 | 1.479 | 0.317 | 85.5 |
| R 4 | 4＂ | 113.030 | 2.309 | 11 | 111.551 | 110.072 | 1.479 | 0.317 | 110.5 |
| R 5 | 5＂ | 138.430 | 2.309 | 11 | 136.951 | 135.472 | 1.479 | 0.317 | 136 |
| R 6 | 6＂ | 163.830 | 2.309 | 11 | 162.351 | 160.872 | 1.479 | 0.317 | 161.5 |
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条