1) suction seal
吸力密封
2) sealing pressure
密封压力
1.
Results show that Kalsi seal has good characteristics such as high sealing pressure,low wear,steady.
结果表明:Kalsi密封结构的“唇部”构造,使密封具备密封压力高、磨损低、扭矩稳定和润滑好等特点;Kalsi密封内接触面从流体动力密封边界一端向外缘,轴向压力呈递增趋势,在“唇部”的波峰(谷)位置应力发生突变至最大值,说明“唇部”动压密封是Kalsi密封的主要表现形式;在相同工况下,Kalsi密封最大密封压力是普通O形密封压力的1。
2.
The packing material with high temperature resistance to 500 ℃ was prepared by taking silicone resin as basic material,powdered aluminum and mica powder as filler,which could endure 500 ℃×36 h ageing process and had sealing pressure greater than or equal to 1 0 MPa.
以有机硅树脂为基料 ,铝粉和云母粉为填料 ,制备了耐 5 0 0℃高温的密封材料 ;该材料经 5 0 0℃× 36h老化实验后 ,密封压力≥ 1 0MPa。
3.
Studies the sealing pressure of the new sealing ring using magnetic fluid establishes the relationships between sealing pressure and width, length of magnetic pole, and sealing clearance, concludes that new type sealing ring has a smaller size and better sealing properties, and compare.
利用磁流体作为密封介质设计了新型径向磁极磁流体密封圈 ,介绍了该密封圈的结构及工作原理 ;给出了耐压能力的数学模型 ,并通过密封间隙中磁场的有限元分析及磁流体流场的分析 ,对该密封圈进行了特性分析 ;给出了密封压力与密封圈磁极长度、磁极宽度和密封间隙三个设计参数之间的变化关系 ,并给出了新型径向磁极密封圈和轴向磁极密封圈的设计比较 。
3) Dynamic seal
动力密封
4) seal moment
密封力矩
1.
The paper expounds the structural characteristics of the tri-eccentric butterfly valve,analyzes the static force acted on the butterfly plank and deduces the seal moment of the tri-eccentric butterfly valve.
本文阐述了三偏心蝶阀的结构特点,从蝶板的静力分析着手,推导出三偏心蝶阀的密封力矩,分析了蝶板厚度、径向偏心距、轴向偏心距以及偏心角对密封力矩的影响。
5) hermetic resistance
密封阻力
1.
Predigested mathematical model of hydraulic hammer and mathematical models considering viscous friction and hermetic resistance were simulated,and the obtained datas were analyzed.
介绍了一种新型液压锤的工作原理,对液压锤的简化数学模型及考虑所受粘性摩擦力、密封阻力的数学模型进行了仿真研究,并对得出的数据进行了分析。
6) seal force
密封力
1.
However, by increasing parameters of the steam and reducing the seal clearance, the seal force from the interaction between the rotor and the labyrinth seal is increased.
但汽轮机蒸汽参数的提高,密封间隙的减小,增大了汽轮机转子密封间产生的密封力,同时由于采用滑动轴承而引起的油膜力,使超超临界汽轮机组转子系统发生失稳的问题越发严重。
补充资料：吸力力
1.象声词。形容摧毁声。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条