1) error bar
误差条线
3) linear error
线性误差
1.
Analysis of linear error of magnetoelectric phase difference type torque rotate speed transducer;
磁电相位差式转矩转速传感器的线性误差分析
2.
The linear error compensation of the resistance respond senor with the polynomial mathematic model is investigated The mathematic compensation model is established, and the error of the simulation vale to the sample is less than 0 02% by 4 times power polynomial, the simulating precision is high The difference between calculation result and actual data is very little after compensatio
研究采用多项式补偿数学模型对应变片式传感器进行线性误差补偿。
3.
This paper introduces the programme for processing the linear error data of the torquemeter with C language,and points out that the computed result of the programme is accurate and can avoid the faults caused by the manual calculation.
介绍了用C语言编写的线性误差数据处理程序,指出该程序计算结果准确,可避免人工计算造成的失误。
4) error curve
误差曲线
1.
The theoretical errors between the beeline method and the design equation were calculated by using Matlab mathematic software,the error curve was drawn,the errors between two design methods were analyzed and discussed.
利用Matlab数学计算软件,对流浆箱锥形布浆总管采用直线法和设计计算公式的理论误差进行了计算并绘制出误差曲线,以此对2种设计方法之间存在的误差进行了分析和探讨,并结合工程实例对得出的优化方案进行了验证。
2.
It is to measure error and error curve of gear′s major specifications, using modularized designing soft ware system and gear′s composition measuring instrument of computer controlling.
提出采用模块化设计软件系统，配用微机控制的齿轮综合测量仪，测出齿轮主要项目的误差和误差曲线的方法，可大大提高测量精确度，效率和可靠性。
3.
The optimum scheme of steering trapezium of four-wheel vehicle is investigated, the steering trapezium is optimized by using three kinds of optimum schemes, a parametric optimum program is developed, the approximation error curves of various schemes is put forward, the optimum results are compared.
对轮式车辆转向梯形优化方案进行了研究,用三种方案对转向梯形进行了优化,编制了参数化的优化程序,给出了各种方案的逼近误差曲线,将优化结果进行了对比。
5) Linearity error
线性误差
1.
Adjusting the linearity error about the balance of Sartorius by using software;
采用软件校正赛多利斯天平线性误差
2.
Radar pulse repetition intervals can be analyzed through simple serial error and linearity error function primary,minimal spanning trees is used in verdict function to extract the PRI model.
通过简单的序列误差和线性误差判决函数对雷达脉冲重频模式进行初步分析,再将聚类方法中的最小张树算法应用于判决函数中去对雷达信号的重频特征进行分析,从而得到了信号的重频模式,为雷达脉冲重频模式识别提供一种新的分析思路,仿真实验验证了算法的有效性。
补充资料：【系统误差】(systematicerror)
【系统误差】(systematicerror)
亦称“恒定误差”。在同一条件下多次测量同一量时，误差的数值和符号保持不变，或在条件改变时，按某一确定的规律变化的误差。产生的主要原因：（1）分析方法不完善。如在重量分析中，由于沉淀的溶解和共沉淀现象等；在职滴定分析中，由于反应进行不完全和*等当点与滴定终点不符合等，均将系统地影响测定结果偏高或偏低。（2）仪器本身不够精确。如砝码重量、容量器皿刻度等。（3）试剂不纯。（4）操作者主观上带来的误差。如对滴定终点颜色的辨别不同等。为保证分析结果的准确度，对这类误差必须尽量减小以致消除。常采用标准试样和标准方法来进行校正，或由不同单位、不同人员测得的结果，进行对照和评价，从而得出校正系数以消除之。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条