1) Ni-W-P coatings
单层镀层
1.
By combining anode polarizing curves and corrosion shape under corresponding electric potential, the corrosion properties of Ni-P/Ni-W-P coatings were studied.
研究表明,Ni-P/Ni-W-P双层镀层的阳极极化曲线具有相当稳定的钝化区,较之相同配方的Ni-W-P单层镀层具有更小的维钝电流密度。
3) Coating
[英]['kəʊtɪŋ] [美]['kotɪŋ]
镀层
1.
Effects of temperature and coatings on wettability of Sn-Cu-Ni lead-free solder;
温度与镀层对Sn-Cu-Ni无铅钎料润湿性能的影响
2.
Determination of metal ions by capillary electrophoresis in coating;
毛细管电泳法测定镀层中金属元素
3.
Relationship between the Distribution of Coating and the Orientation of Cathode in Composite Coating;
复合镀中镀层分布与阴极位向的关系
4) Coat
[英][kəʊt] [美][kot]
镀层
1.
Experiment of Compound Coating with(Ni/SiC)_P as Second Phase Particle;
(Ni/SiC)_P为第二相粒子的复合镀层研究
2.
To introduce the determination of rare earth content in Zn-Al-RE alloy coat using the C 24 H 18 ClN 4O 12 PS 2-m A spectrophotometry.
介绍用偶氮氯膦—mA分光光度法测定锌 -铝 -稀土合金镀层中的稀土量。
3.
It is shown by test that adding minute quantity Al to pure Zn coating liquid can make the surface of coated steel wire appear silvering,adding about 0.
2 %Al能抑制钢丝镀层Fe -Zn合金层的生长 ;适用于通常热镀锌工艺条件的Al含量以 0 。
5) plating layer
镀层
1.
In this paper,a magnetoresistance sensor with difference structure is designed,so the problem of small signal and large disturbance in the magnetic leakage testing for the parts with plating layer is solved.
针对镀层工件漏磁检测中检测信号微弱,干扰信号相对于缺陷信号大等特点,采用具有差分结构的磁阻传感器设计,对传感器信号进行放大、滤波处理,对传感器进行置复位、增益和偏差调整电路设计,取得了满意效果。
2.
Polarization curves show that the Ni-P plating layer has long passivation district and better corrosion resistance in the 3.
研究了压铸镁合金AZ91的表面化学镀镍磷合金的工艺,利用X射线衍射(XRD)、扫描电镜(SEM)、能谱(XPS)及极化曲线的测量等方法,探讨了镁合金表面化学镀Ni-P层的组织、相、成分及其耐蚀性,结果显示,镁合金化学镀Ni-P合金镀层在350℃热处理后成晶态,镀层成分为NiP、Ni2P等。
3.
One technological problem about the weak combination of interface between Cr plating layer and substrate which was strengthened by plasma had been put forward according to the application state of under serious ablation and erosion by hot chemical airflow.
针对高温化学气流冲刷烧蚀的使用状态,提出了等离子束流界面强化解决镀Cr层与基体结合强度不足的技术问题,用非转移等离子束流对镀铬钢件表面进行快速加热进行界面强化处理的工艺方法,介绍了等离子束流界面强化原理,进行了等离子束流强化工艺试验,并对试验结果进行了检测和分析研究,结果表明,镀Cr层与基体产生了冶金结合,较为显著地提高了镀层与基体的结合强度。
6) plating
[英]['pleɪtɪŋ] [美]['pletɪŋ]
镀层
1.
Effect of plating on adhesion property between steel cord and rubber;
镀层对钢丝帘线与橡胶粘合性能的影响
2.
Research of accelerated corrosion test method of zinc, cadmium plating on high-strength steel;
高强度钢锌、镉镀层加速腐蚀试验方法研究
3.
Determination of Plating or Coating Thickness by Isotopic X_Ray Fluorescence Spectrometry;
工业镀层及涂层厚度分析——同位素X射线荧光光谱法
补充资料：装箱单、重量单、尺码单
装箱单、重量单、尺码单
[装箱单、皿t单、尺码单1装箱单(Pack-ing Ust)是说明货物包装情况的单据，包括包装材料、包装方式，以及详细的包装内容，如花色、规格搭配等。进口地海关主要依据装箱单对某一特定内容的包装内容进行检查，也是进口商核对货物的依据。装箱单的内容有:单据名称、卖方名称、唆头、件数、规格、数量、毛净重、签字等。 重量单(Weight ust)是由卖方或第三者提供的，表明货物重量的单据。一般包括皮、毛、净重。它必须和其他单据上所表示的货物重量一致。 尺码单就不详细介绍了。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条