1) impact and abrasion mechanism
冲击磨损机制
2) impact wear mechanism
冲击磨损机理
3) impact wear
冲击磨损
1.
The impact wear behavior of AZ91D magnesium alloys in de-ionized water;
AZ91D镁合金在水介质下的冲击磨损特性研究
2.
Study on Impact Wear Properties of Composite Layer with Tungsten and Chromium;
钨铬复合铸渗层的冲击磨损性能研究
3.
TiC_p Interfacial structure and impact wear resistance of TiC p/Ni coating by laser cladding;
激光熔覆涂层中TiC_p界面结构与涂层冲击磨损性能
4) impact abrasion
冲击磨损
1.
The impact abrasion performance of martensite steel was studied.
对马氏体细晶粒高强度钢的冲击磨损性能进行了研究。
2.
The impact abrasion properties of CrMnMo martensitic liner board steel and CrNiMo martensitic liner board steel were tested with MLDF-10 wear tester in acid-ironstone slurry.
采用MLDF-10冲击腐蚀磨损试验机研究了CrMnMo马氏体衬板钢和CrNiMo马氏体衬板钢在铁矿石酸性矿浆中的冲击磨损特性。
3.
The impact abrasion tests were performed,and both hardness and wear loss of the samples were compared with classical surfacing electrode D256.
经过对制备的试样分别进行多次冲击磨损试验,并与D256焊条进行对比试验,分析试样的硬度和磨损失重变化,结果表明,此种堆焊材料具有焊接工艺性好、堆焊层组织加工硬化率高和耐凿削式冲击磨损性能优异的特点。
5) erosion wear mechanism
冲蚀磨损机制
1.
The erosion wear surfaces of 40Cr and 45# steel were observed on the scanning electron microscope (SEM),it is showed that the erosion wear mechanism of 40Cr and 45# steel is the micro-cutting effect of hard sand on the material surface.
在电子显微镜(SEM)下对40Cr和45#钢冲蚀磨损表面形貌进行观察,分析表明40Cr和45#钢的冲蚀磨损机制都是硬质砂粒对材料表面的微切削作用。
2.
The erosion wear surfaces of QT500 and HT200 were observed on the scanning electron microscope(SEM),it is showed that the erosion wear mechanism of QT500 is the hard sand's micro-cutting effect on the material's surface,and the mechanism of HT200 is the brittlen.
在电子显微镜(SEM)下对QT500和HT200冲蚀磨损表面形貌进行观察,分析表明:QT500的冲蚀磨损机制是硬质砂粒对材料表面的微切削作用,而HT200的冲蚀磨损机制是因赫兹裂纹导致的脆性脱落。
6) wear impact energy
磨损冲击功
补充资料：标准操作冲击电压波形(见冲击电压发生器)
标准操作冲击电压波形(见冲击电压发生器)
standard switching impulse voltage waveform
b .oozhun CooZuo ChongJld，onyo boxlng标准操作冲击电压波形(standard switchingimpulse voltage waveform)见冲击电压发生器。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条